CITJobs In Plumbing
Guide

PEX vs. Copper vs. CPVC vs. Cast Iron: What Apprentices Learn

Homeowner guides ask which pipe is best. Apprentices need to know how to identify, join, support and test every one of them. Here is the working knowledge.

Jobs In Plumbing Editorial8 min read

Key takeaways

  • Copper Type K is green-coded, Type L blue and Type M red; all three fall under ASTM B88, and DWV copper is yellow under ASTM B306.
  • Typical PEX tubing is rated 160 psi at 74°F, 100 psi at 180°F and 80 psi at 200°F, and it should not live in sunlight.
  • CPVC water pipe made to ASTM D2846 is commonly rated for 100 psi at 180°F and joins with primer and solvent cement.
  • Cast iron stays in the DWV world, especially main stacks and commercial work, because it is noncombustible and quieter than plastic.
  • Since the 2011 Reduction of Lead in Drinking Water Act, wetted surfaces may average no more than 0.25% lead and solder no more than 0.2%.

Search for PEX vs copper vs CPVC and you will find a hundred homeowner articles asking which pipe is best. As an apprentice, you need a different answer. You will work with every one of these materials, often in the same building, and sometimes on the same afternoon when you are tying new PEX into old copper above a cast iron stack. What you need to know is how to identify each one on sight, what it is rated for, how it joins and where the code lets it go.

This guide covers the four materials apprentices meet most, plus PVC and ABS for drainage, using manufacturer, industry and EPA data. Your state's adopted code always has the final word on where a material is allowed. For which code that is, see UPC vs. IPC.

Quick Reference: Supply and Drain Materials

MaterialMain useHow it joinsKey ratings or limitsWatch out for
PEXHot and cold water supply; radiant heat (barrier tubing)Crimp or clamp rings, expansion, push-to-connect160 psi at 74°F, 100 psi at 180°F, 80 psi at 200°F (typical listing)Sunlight, minimum bend radius, thermal expansion
Copper (K, L, M)Water supply, also gas and other services where allowedSoldering, brazing, press, compression, push-to-connectWall thickness rises from M to L to KSkilled labor, fire risk while sweating, cost
CPVCHot and cold water supplyPrimer and solvent cement; push-to-connect100 psi at 180°F (ASTM D2846 pipe)Brittle when cold; cure times; more fittings at turns
Cast ironDrain, waste and vent; stacks; commercialHubless couplings or hub-and-spigotNoncombustibleWeight, rust over time in older systems
PVCDWV and cold waterPrimer and solvent cementCold only; can warp with hot waterSunlight makes it brittle
ABSDWVSolvent cementHandles hotter drain water than PVCBlack color; not allowed everywhere

Ratings above come from the manufacturer and supplier pages cited in each section below.

PEX: Fast, Flexible and Picky About Fittings

Cross-linked polyethylene has taken over a big share of residential water supply because it is light, flexible, cheaper than copper and quick to install. One coil can run from a manifold to a fixture with no joints in the wall.

What apprentices need to know:

  • Ratings: A typical potable PEX listing on PexUniverse's technical page shows 160 psi at 74°F, 100 psi at 180°F and 80 psi at 200°F.
  • Standards: The tubing is made to ASTM F876 and the hot and cold systems to ASTM F877. Potable tubing carries NSF/ANSI 61 and 372 listings; oxygen-barrier tubing for radiant heat carries NSF 14 for that use.
  • Fittings must match the system. Copper crimp rings follow ASTM F1807 and stainless clamps follow ASTM F2098. Expansion systems use their own fittings. Push-to-connect works with any type. Mixing brands and methods without checking the manufacturer's instructions is how leaks happen.
  • Bending and expansion: The same page lists a minimum bend radius of 8 times the outside diameter and notes PEX grows roughly 1 to 2.5 inches per 100 feet for a 10°F rise. Leave slack and do not pull runs tight.
  • Sunlight: Home Depot's pipe guide warns that PEX can turn brittle with sun exposure and should not be used outdoors. Keep coils covered on site.
  • Testing: For potable plumbing, PexUniverse lists a test at 1.5 times maximum working pressure without exceeding the pipe's rating at temperature, held at least 30 minutes. Follow your code and local inspector.

Copper: Types K, L and M and Why the Color Matters

Copper is the material older plumbers grew up on, and you will spend years repairing and tying into it. The first skill is reading the stripe. According to the Copper Development Association's tube table:

TypeColor codeStandardNotes
KGreenASTM B88Thickest wall; available in straight lengths and coils
LBlueASTM B88Middle wall; available in straight lengths and coils
MRedASTM B88Thinnest wall; straight lengths only
DWVYellowASTM B306Drain, waste and vent
ACRBlueASTM B280Air conditioning and refrigeration

Wall thickness is the real difference. Ferguson's comparison lists half-inch walls of 0.028 inch for M, 0.040 for L and 0.049 for K. Its working-pressure figures for half-inch tube at 150°F are about 285 psi for M, 420 psi for L and 540 psi for K. Ferguson's guidance is to use L for most indoor potable water and K for underground services, but the CDA table lists potable water as an application for all three. Which types your jurisdiction allows for which jobs is a code question, so ask your journeyman and check the local amendments.

Lead-free rules for copper work

Every apprentice who sweats copper should know the federal lead rules. The EPA explains that the Safe Drinking Water Act limits solder and flux to 0.2% lead. The 2011 Reduction of Lead in Drinking Water Act cut the limit for wetted surfaces of pipes, fittings and fixtures from 8% to a weighted average of 0.25%. In practice, that means lead-free solder and listed fittings on any potable line. Old 50/50 solder on the truck stays off drinking water.

CPVC: The Rigid Plastic Option for Hot Water

CPVC is a rigid, cream-colored plastic sized to match copper tube, so it can replace copper in residential supply. Ferguson's listing for a common brand of SDR 11 CPVC made to ASTM D2846 says it is for systems that will not exceed 180°F at 100 psi, with NSF 14 and NSF 61 certification.

Key habits:

  • Primer and cement: Most CPVC joins with primer and solvent cement. Use products made for CPVC and respect cure times before pressure testing.
  • More fittings: Because it is rigid, CPVC needs elbows at every turn, which means more joints to get right. The VDCI materials comparison points this out as its main downside compared with PEX.
  • Handling: Rigid plastic can crack if dropped or cut carelessly, especially in cold weather. Cut square, deburr and bevel before cementing.

Cast Iron: The Drain Pipe That Stays Quiet

Cast iron is a drain, waste and vent material, not a supply pipe. You will find it in older homes as the main stack and in plenty of new commercial buildings. The Cast Iron Soil Pipe Institute says American-made cast iron is noncombustible and can be used in return air plenums. CISPI also claims cast iron is quieter than all-plastic drain systems because of its material structure. That claim comes from an industry group, but the noise difference is a common reason architects specify it for apartments, hotels and offices.

Two joining systems to learn:

  • Hubless (no-hub): Plain-end pipe and fittings joined with a gasket and band coupling. CISPI 301 is the standard specification for hubless pipe and fittings.
  • Hub-and-spigot: The spigot end sits in a bell, sealed with a gasket. Older systems used lead and oakum. Home Depot's guide recommends leaving hub-and-spigot installation to professionals, which is a good reminder that this is trade work.

Cast iron is heavy. Support it properly, cut it with the right tool and get help on stack work. The physical reality of plumbing covers how to save your back on jobs like this.

PVC, ABS and Galvanized: The Rest of the Pipe Rack

  • PVC: White or gray plastic used for DWV and cold water. It can warp with hot water and gets brittle in sunlight. VDCI calls it the standard for many residential and commercial drain systems.
  • ABS: Black plastic DWV pipe. It handles hotter drain water than PVC, according to Home Depot, and VDCI notes it is often used in colder climates. Some jurisdictions restrict it, so check your code.
  • Galvanized steel: You will mostly see it when you are taking it out. It was common in water supply until the 1960s. The zinc coating wears off, the pipe rusts from the inside and flow drops.

Apprentice Checklist: Materials Skills to Master

  • Identify K, L, M and DWV copper by color stripe and wall feel
  • Sweat a clean, lead-free copper joint and know when press fittings are allowed
  • Make crimp, clamp and expansion PEX connections with the correct tool and rings
  • Prime and cement CPVC and PVC with the right products and cure times
  • Install a no-hub coupling to the manufacturer's torque spec
  • Transition between materials with listed fittings (for example, PEX to copper or cast iron to PVC)
  • Know the pressure test procedure your code requires for supply and DWV
  • Read the print line on any pipe to find its standard, size and listing

These skills show up on the job long before they show up on a test, and they are some of the first things a good foreman will check. If you are building your kit, start with the essential tools for apprentices.

Bottom Line

There is no single best pipe, and apprentices who think that way get caught out. PEX wins on speed and flexibility in residential supply, copper is the standard you will repair and tie into for decades, CPVC is the rigid plastic option for hot and cold water, and cast iron rules quiet, fire-rated drain stacks. Learn to identify, join, support and test every one of them, and let your local code decide where each goes.

Gear mentioned in this guide

As an Amazon Associate, Jobs In Plumbing earns from qualifying purchases. Prices and availability change; check current listings.

Frequently asked questions

Which is better, PEX or copper?

It depends on the job. PEX is lighter, more flexible and generally cheaper to install, with fewer fittings. Copper is rigid, durable and can handle sunlight and higher temperatures, but it costs more and takes more skilled labor. Many shops use PEX for new residential supply and copper where codes, customers or conditions call for it.

What do the colors on copper pipe mean?

The color stripe identifies the wall thickness. According to the Copper Development Association, Type K is green, Type L is blue and Type M is red, all under ASTM B88. DWV copper is yellow (ASTM B306), and ACR refrigeration tubing is blue (ASTM B280).

How hot can CPVC pipe get?

CPVC water distribution pipe made to ASTM D2846 is commonly rated for 180°F at 100 psi, as shown on supplier listings for SDR 11 CPVC. That covers normal domestic hot water. Always check the print line and the manufacturer's data for the exact product you are installing.

Why is cast iron still used for drains?

Cast iron is noncombustible, which matters in fire-rated construction and return air plenums, and the Cast Iron Soil Pipe Institute says it is much quieter than plastic drain piping. That makes it a common choice for main stacks, apartments, hotels and commercial buildings, even though it is heavier to install.

Looking for plumbing work?

Tell us your trade, location and experience. The Careers In Trades network routes you to employers who are actually hiring. Free for workers.

Sources

  1. Copper Development Association — Copper Tube Handbook, Table 1: Copper tube types and color codes
  2. Ferguson — Type M vs. Type L vs. Type K copper pipe
  3. PexUniverse — PEX tubing technical specs
  4. Ferguson — 1 in. x 20 ft. SDR 11 FlowGuard Gold CPVC pressure pipe (product specs)
  5. Cast Iron Soil Pipe Institute — Home
  6. Cast Iron Soil Pipe Institute — Sound Attenuation
  7. U.S. EPA — Use of Lead Free Pipes, Fittings, Fixtures, Solder and Flux for Drinking Water
  8. Home Depot — Types of Plumbing Pipes

Pay, licensing and program details change and vary by state, employer and local agreement. Verify with the linked sources and your state licensing board before making decisions.